How much bacteriostatic water do I add to 10mg of Epithalon?

The standard protocol is to add 2 ml of bacteriostatic water to a 10 mg vial of Epithalon. This produces a concentration of 5.00 mg/ml (5000 mcg/ml). Adjust the water volume down if you want a more concentrated solution for smaller syringe volumes, or up if you prefer easier-to-read markings.

What is the standard dose of Epithalon after reconstitution?

A common Epithalon research dose is 5.0 mg per administration. At a concentration of 5.00 mg/ml, this equals approximately 100.0 IU on a 100-unit insulin syringe (1.000 ml per dose). Always confirm your dose against your protocol — this is a starting reference only.

How long does reconstituted Epithalon last in the fridge?

Reconstituted Epithalon in bacteriostatic water typically remains stable for 28 days refrigerated at 2–8°C (36–46°F). BAC water contains 0.9% benzyl alcohol as a preservative. Never freeze, never leave at room temperature, and discard if the solution becomes cloudy or discolored.

What concentration does 10mg Epithalon in 2ml water give?

10 mg of Epithalon reconstituted in 2 ml of BAC water produces a concentration of 5.00 mg/ml, which equals 5000 mcg/ml. This vial yields roughly 2 full doses at 5000 mcg per administration.

Can I use sterile water instead of BAC water for Epithalon?

You can, but it is not recommended for multi-dose vials. Sterile water has no benzyl alcohol preservative, so reconstituted Epithalon must be used within 24 hours. BAC water allows the vial to last 28 days refrigerated. Use sterile water only if you plan to finish the entire vial in a single session.

🔬 100K+ researchers trust BodyHackGuide — Join r/BodyHackGuide

How to Reconstitute Epithalon

Pre-filled calculator with standard defaults for Epithalon: 10 mg vial in 2 ml BAC water.

Standard Epithalon Reconstitution Protocol

Add 2 ml of bacteriostatic water to a 10 mg vial of Epithalon. This gives a concentration of 5.00 mg/ml. A standard 5000 mcg dose equals about 100.0 IU on a 100-unit insulin syringe. Store refrigerated at 2–8°C and use within 28 days.

Vial Size

BAC Water

Desired Dose

mcg

Concentration

5.00

mg/ml

5000 mcg/ml

Dose Volume

1.000

Per dose

Syringe Draw

100.0

100-unit insulin syringe

Doses per Vial

doses

2.0 exact

Draw to

100

100.0 units

Draw to this line

Step-by-Step: How to Reconstitute Epithalon

1

Gather your supplies

A sealed 10 mg vial of Epithalon, a vial of bacteriostatic water, a 1 ml (100-unit) insulin syringe, and an alcohol swab.
2

Inject the water

Wipe both vial stoppers with alcohol. Draw 2 ml of BAC water into the syringe and inject it slowly down the inside wall of the Epithalon vial. Never spray directly onto the powder — the force can damage the peptide.
3

Swirl gently

Gently swirl the vial in a circular motion until the Epithalon fully dissolves. Do not shake. The solution should become clear.
4

Calculate your dose

At a concentration of 5.00 mg/ml, a 5000 mcg (5.000 mg) dose equals about 100.0 IU on a 100-unit insulin syringe.
5

Draw and store

Draw your dose, perform the injection, and immediately return the vial to the refrigerator at 2–8°C. Use the reconstituted vial within 28 days.

These defaults reflect the most common community protocols for Epithalon. Individual research protocols may differ. Always verify against your source and consult a qualified practitioner before any injection. BodyHackGuide publishes for research and educational purposes only.

Epithalon Reconstitution FAQ

More Epithalon Resources

Epithalon compound page Epithalon dosage guide General reconstitution calculator Verify your Epithalon COA

Free 2026 Peptide Cheat Sheet — 50 pages, PDF

Dosing, reconstitution, stacks, half-lives, and vendor trust tiers. The reference we wish we had on day one.

Download Free