How much bacteriostatic water do I add to 2mg of DSIP?

The standard protocol is to add 2 ml of bacteriostatic water to a 2 mg vial of DSIP. This produces a concentration of 1.00 mg/ml (1000 mcg/ml). Adjust the water volume down if you want a more concentrated solution for smaller syringe volumes, or up if you prefer easier-to-read markings.

What is the standard dose of DSIP after reconstitution?

A common DSIP research dose is 100 mcg per administration. At a concentration of 1.00 mg/ml, this equals approximately 10.0 IU on a 100-unit insulin syringe (0.100 ml per dose). Always confirm your dose against your protocol — this is a starting reference only.

How long does reconstituted DSIP last in the fridge?

Reconstituted DSIP in bacteriostatic water typically remains stable for 14 days refrigerated at 2–8°C (36–46°F). BAC water contains 0.9% benzyl alcohol as a preservative. Never freeze, never leave at room temperature, and discard if the solution becomes cloudy or discolored.

What concentration does 2mg DSIP in 2ml water give?

2 mg of DSIP reconstituted in 2 ml of BAC water produces a concentration of 1.00 mg/ml, which equals 1000 mcg/ml. This vial yields roughly 20 full doses at 100 mcg per administration.

Can I use sterile water instead of BAC water for DSIP?

You can, but it is not recommended for multi-dose vials. Sterile water has no benzyl alcohol preservative, so reconstituted DSIP must be used within 24 hours. BAC water allows the vial to last 14 days refrigerated. Use sterile water only if you plan to finish the entire vial in a single session.

How much bacteriostatic water do I add to 2mg of DSIP?

The standard protocol is to add 2 ml of bacteriostatic water to a 2 mg vial of DSIP. This produces a concentration of 1.00 mg/ml (1000 mcg/ml). Adjust the water volume down if you want a more concentrated solution for smaller syringe volumes, or up if you prefer easier-to-read markings.

What is the standard dose of DSIP after reconstitution?

A common DSIP research dose is 100 mcg per administration. At a concentration of 1.00 mg/ml, this equals approximately 10.0 IU on a 100-unit insulin syringe (0.100 ml per dose). Always confirm your dose against your protocol — this is a starting reference only.

How long does reconstituted DSIP last in the fridge?

Reconstituted DSIP in bacteriostatic water typically remains stable for 14 days refrigerated at 2–8°C (36–46°F). BAC water contains 0.9% benzyl alcohol as a preservative. Never freeze, never leave at room temperature, and discard if the solution becomes cloudy or discolored.

What concentration does 2mg DSIP in 2ml water give?

2 mg of DSIP reconstituted in 2 ml of BAC water produces a concentration of 1.00 mg/ml, which equals 1000 mcg/ml. This vial yields roughly 20 full doses at 100 mcg per administration.

Can I use sterile water instead of BAC water for DSIP?

You can, but it is not recommended for multi-dose vials. Sterile water has no benzyl alcohol preservative, so reconstituted DSIP must be used within 24 hours. BAC water allows the vial to last 14 days refrigerated. Use sterile water only if you plan to finish the entire vial in a single session.

100K+ researchers trust BodyHackGuide — Join r/BodyHackGuide

How to Reconstitute DSIP

Pre-filled calculator with standard defaults for DSIP: 2 mg vial in 2 ml BAC water.

Standard DSIP Reconstitution Protocol

Add 2 ml of bacteriostatic water to a 2 mg vial of DSIP. This gives a concentration of 1.00 mg/ml. A standard 100 mcg dose equals about 10.0 IU on a 100-unit insulin syringe. Store refrigerated at 2–8°C and use within 14 days.

Vial Size

BAC Water

Desired Dose

mcg

Concentration

1.00

mg/ml

1000 mcg/ml

Dose Volume

0.100

Per dose

Syringe Draw

10.0

100-unit insulin syringe

Doses per Vial

doses

20.0 exact

Draw to

100

10.0 units

Draw to this line

DSIP Reconstitution Chart

Common syringe draws at the standard DSIP preset (2 mg in 2 mL BAC water = 1.00 mg/mL). Units are on a U-100 insulin syringe (100 units = 1 mL). For laboratory research reference only.

Syringe units (U-100)	Volume	Amount (DSIP)
5 units	0.05 mL	50 mcg
10 units	0.10 mL	100 mcg
15 units	0.15 mL	150 mcg
20 units	0.20 mL	200 mcg
25 units	0.25 mL	250 mcg
30 units	0.30 mL	300 mcg
40 units	0.40 mL	400 mcg
50 units	0.50 mL	500 mcg

Change the vial size or BAC water above to recompute the chart for a different DSIP preset. This chart shows reconstitution math, not a dosing recommendation.

Step-by-Step: How to Reconstitute DSIP

1

Gather your supplies

A sealed 2 mg vial of DSIP, a vial of bacteriostatic water, a 1 ml (100-unit) insulin syringe, and an alcohol swab.
2

Inject the water

Wipe both vial stoppers with alcohol. Draw 2 ml of BAC water into the syringe and inject it slowly down the inside wall of the DSIP vial. Never spray directly onto the powder — the force can damage the peptide.
3

Swirl gently

Gently swirl the vial in a circular motion until the DSIP fully dissolves. Do not shake. The solution should become clear.
4

Calculate your dose

At a concentration of 1.00 mg/ml, a 100 mcg (0.100 mg) dose equals about 10.0 IU on a 100-unit insulin syringe.
5

Draw and store

Draw your dose, perform the injection, and immediately return the vial to the refrigerator at 2–8°C. Use the reconstituted vial within 14 days.

These defaults reflect the most common community protocols for DSIP. Individual research protocols may differ. Always verify against your source and consult a qualified practitioner before any injection. BodyHackGuide publishes for research and educational purposes only.

DSIP Reconstitution FAQ

More DSIP Resources

DSIP compound page DSIP dosage guide General reconstitution calculator Verify your DSIP COA

Free 2026 Peptide Cheat Sheet — 50 pages, PDF

Dosing, reconstitution, stacks, half-lives, and vendor trust tiers. The reference we wish we had on day one.

Download Free